PROFESSIONAL FLAT DISPLAY MONITOR
GXD-L52H1
PROTOCOL MANUAL
1st Edition
Table of Contents
1. Communication Parameters ......................................................... 1
2. Pin Assignment..................................................................................... 1
3. Communication Data Format ....................................................... 1
4. General Function ................................................................................. 3
5. Analog Signal Detect Function ................................................... 8
6. Priority Signal Select Function ................................................... 9
7. Picture/Sound ...................................................................................... 14
8. Size/Shift ................................................................................................. 17
9. Status Enquiry ..................................................................................... 20
10. User Reset.............................................................................................. 25
11. Service...................................................................................................... 25
GXD-L52H1
1. Communication Parameters
3. Communication Data Format
(a) Control message
Communication method
Synchronous method
Baud rate
RS-232C
Asynchronous
9600bps
8bit
No.
Item
Value
1
Header
0x8C: Control
0xXX
Character length
Parity
2
Category
Function
Data1 (Length)
Data2 (Data1)
:
None
3
0xXX
Start bit length
Stop bit length
Flow control
1bit
4
0xXX
1bit
5
0xXX
None
:
0xXX
:
:
0xXX
X
DataX
0xXX
2. Pin Assignment
X+1
Check Sum
0xXX
* Check Sum: Sum total of 1 to X. Lower one-byte data is validated when a
value exceeds 255 (1byte).
Monitor side (D-sub 9-pin)
Host side (D-sub 9-pin)
* Set the command interval to 500 ms or more when transmitting the
Control command continuously.
5
4
3
2
1
5
4
3
2
1
* Set the command interval to 500 ms or more when transmitting the same
command (Enquiry) after the Control command.
9
8
7
6
9
8
7
6
_ External view _
_ External view _
(b) Enquiry message
Pin No. Function
Pin No. Function
No.
Item
Value
1
2
3
4
5
6
7
8
9
NC
TXD
RXD
NC
1
2
3
4
5
6
7
8
9
NC
RXD
TXD
NC
1
2
3
4
5
6
Header
0x83: Enquiry
0xXX
Category
Function
Data1
0xXX
GND
NC
GND
NC
0xFF
NC
NC
Data2
0xFF
NC
NC
Check Sum
0xXX
NC
NC
* Check Sum: Sum total of 1 to X. Lower one-byte data is validated when a
value exceeds 255 (1byte).
GXD-L52H1
1
(c) Answer message
4 Error answer
1 Control answer
No.
Item
Value
No.
1
Item
Value
1
2
Header
Answer
0xE0: Answer
Header
Answer
0x70: Answer
*
0x00: No Function Error
0x01: Check Sum Error
0x02: Data Length Error
0xXX
*
2
0x00: Completed
0x01: Limit Over
0x02: Limit Under
0x03: Command Canceled
0xXX
3
Check Sum
* 0x00: No Function Error
0x01: Check Sum Error
0x02: Data Length Error
Packet header,category or function code are
not included in this protocol.
Check sum value or received packet is not
correct.
Packet is correctly received,but the data size
is over the upper limit.
3
Check Sum
* 0x00: Completed
0x01: Limit Over
Packet is correctly received and process
is also correctly completed.
Packet is correctly received, but the data
value is over the upper limit.
0x02: Limit Under
Packet is correctly received, but the data
value under the lower limit.
0x03: Command Canceled
Packet is correctly received, but the data
value is not correct or the request cannot
be accepted in the current host state.
Sum total of 1 to X. Lower one-byte data
is validated when a value exceeds 255
(1byte).
* Check Sum:
2 Enquiry answer (Complete)
No.
Item
Value
1
Header
Answer
0x70: Answer
2
0x00: Completed
3
Return Data Size 0xXX
4
Return Data1
0xXX
0xXX
0xXX
0xXX
0xXX
:
:
:
:
X
Return DataX
Check Sum
X+1
* 0x00: Completed Packet is correctly received and process is also
correctly completed.
* Return Data:
Returns the read value.
* Check Sum:
Sum total of 1 to X. Lower one-byte data is validated
when a value exceeds 255 (1byte).
3 Enquiry answer (Command cancel)
No.
Item
Value
1
2
3
Header
0x70: Answer
Answer
0x03: Command Canceled
0x73
Check Sum
0x03: Command Canceled
Packet is correctly received, but the data
value is not correct or the request cannot
be accepted in the current host state.
GXD-L52H1
2
4. General Function
(a) Mode Control
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
Enquiry
0x8C
0x83
0x00
Code Table (1-a) [a]
0x02
0xFF
Code Table (1-a) [b]
0xFF
0xXX
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x01
0x02
0x03
0x70
0x71
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Code Table (1-a) [b]
Check Sum
0xXX
Enquiry
0x70
0x00
0x02
Completed
Code Table (1-a)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Standby
Power On
0x00
0x01
Power
0x00 OFF
Yes
Yes
Enable
Enable
0x01 ON
*4
Input Select
0x08 HD15 RGB
0x09 HD15 YUV
0x0E OPTION RGB
0x0F OPTION COMPONENT
0x20 DVI
Yes
Yes
Disable
Enable
0x30 VIDEO
0x31 S-VIDEO
0x44 HDMI
0x84 Option Digital1 (HDMI1/SDI)
0x85 Option Digital2 (HDMI2)
0x02
0x03
0x04
Force Status Display 0x00 ON
0x01 OFF
Yes
Yes
Yes
Yes
Yes
Yes
Disable
Disable
Enable
Enable
Enable
Enable
Audio Mute
0x00 OFF
0x01 ON
0x00 ON
0x01 OFF
Auto Status Display
(Continued)
GXD-L52H1
3
Code Table (1-a)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Standby
Power On
0x06
Color System
0x00 Auto
Yes
Yes
Disable
Enable
0x01 NTSC
0x02 NTSC4.43
0x03 PAL
0x05 PAL-M
0x06 PAL-N
0x07 PAL60
0x0F
Language
0x00 Japanese
0x01 English
0x02 Deutsch
0x03 Français
0x04 Español
0x05 Italiano
0x01-0xFF
Yes
Yes
Disable
Enable
0x10
0x12
Index Number
Standby Power
Yes
Yes
Yes
Yes
Disable
Disable
Enable
Enable
0x00 Standard
0x01 Low
0x13
ECO Mode
0x00 Off
Yes
Yes
Disable
Enable
(Power Saving)
0x01 ECO High
0x02 ECO Low
0x00 ON
0x14
0x18
0x1B
0x24
Speaker Out
Sync Mode
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Disable
Disable
Disable
Disable
Enable
Enable
Enable
Enable
0x01 OFF
0x00 H/Comp
0x01 Video
Clock Display
0x00 OFF
0x01 ON
Input Detect
(Option)
0x00 FW12 (HD15)
0x02 FW11 (BNC)
0x03 Reserved
0x05 FW50 (RGB)
0x06 FW21 (UART + CTRL-S)
0x08 FW15 (HDMI x 2)
0x09 FW16 (HD-SDI)
0x0A Reserved
0x0B Reserved
0x0C Reserved
0x0D Reserved
0x0E Reserved
0x0F Not Connect
(Continued)
GXD-L52H1
4
Code Table (1-a)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Standby
Power On
0x26
0x27
0x30
Auto Shut OFF
0x00 OFF
Yes
Yes
Yes
Yes
Disable
Enable
0x01 ON
Auto Screen Adjust
PAP
0x00 OFF
Yes
Yes
Disable
Disable
Enable
Enable
0x01 ON
0x00 OFF
0x01 P&P
0x02 PinP
0x31
Active Picture
0x00 Left (P&P)/Main (PinP)
0x01 Right (P&P)/Sub (PinP)
0x02 Swap
Yes
Yes
Disable
Enable
0x32
0x33
Picture Size (P&P)
0x00-0x0E
Yes
Yes
Yes
Yes
Disable
Disable
Enable
Enable
Sub Picture Size
(PinP)
0x00 Large
0x01 Small
0x34
Picture Position
(PinP)
0x00 Position1
Yes
Yes
Disable
Enable
0x01 Position2
0x02 Position3
0x03 Position4
0x35
PAP Input Detect
(Left/Main)
0x08 HD15 RGB
0x09 HD15 YUV
0x0E OPTION RGB
0x0F OPTION COMPONENT
0x20 DVI
No
Yes
Disable
Enable
0x30 VIDEO
0x31 S-VIDEO
0x44 HDMI
0x84 Option Digital1 (HDMI1/SDI)
0x85 Option Digital2 (HDMI2)
0x08 HD15 RGB
0x09 HD15 YUV
0x0E OPTION RGB
0x0F OPTION COMPONENT
0x20 DVI
0x36
PAP Input Detect
(Right/Sub)
No
Yes
Disable
Enable
0x30 VIDEO
0x31 S-VIDEO
0x44 HDMI
0x84 Option Digital1 (HDMI1/SDI)
0x85 Option Digital2 (HDMI2)
(Continued)
GXD-L52H1
5
Code Table (1-a)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Standby
Power On
0x40
0x41
Screen Saver
0x00 OFF
Yes
Yes
Disable
Enable
0x01 All White ON
0x02 Sweep ON
0x00 Gray
BackGround
Yes
Yes
Disable
Enable
0x01 Dark Gray
0x02 Black
0x43
0x44
Back Light
0x00-0x64
Yes
Yes
Yes
Yes
Disable
Enable
Enable
Enable
Logo Illumination
0x00 Logo Off
0x01 Logo On (Low)
0x02 Logo On (High)
0x00 Main + Remocon
0x01 Main
0x45
Control Mode
Yes
Yes
Disable
Enable
0x02 Remocon
0x03 All Off
*5
0x04 Limited
0x46
0x47
On Off Timer Mode
On Timer Enable
0x00 Every Day (Repeat)
0x01 Day Of Week
Yes
Yes
Yes
Yes
Enable
Enable
Enable
Enable
bit0
bit1
bit2
bit3
bit4
bit5
bit6
bit7
bit0
bit1
bit2
bit3
bit4
bit5
bit6
bit7
Sunday 1: Enable, 0: Disable
Monday 1: Enable, 0: Disable
Tuesday 1: Enable, 0: Disable
Wednesday 1: Enable, 0: Disable
Thursday 1: Enable, 0: Disable
Friday 1: Enable, 0: Disable
Saturday 1: Enable, 0: Disable
Every day 1: Enable, 0: Disable
0x48
Off Timer Enable
Sunday 1: Enable, 0: Disable
Monday 1: Enable, 0: Disable
Tuesday 1: Enable, 0: Disable
Wednesday 1: Enable, 0: Disable
Thursday 1: Enable, 0: Disable
Friday 1: Enable, 0: Disable
Saturday 1: Enable, 0: Disable
Every day 1: Enable, 0: Disable
Yes
Yes
Enable
Enable
0x65
0x66
IP Setting Mode
0x00 DHCP
Yes
Yes
Yes
Enable
Enable
Enable
Enable
0x01 Manual
0x02 Speed
IP Setting Execute
0x00 Shut Down
0x01 IP Setting
0x02 NVR Reset
0x03 Alarm
No
(Continued)
GXD-L52H1
6
Code Table (1-a)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Standby
Power On
0x67
IP Setting Result
0x00 Done
Yes
No
Enable
Enable
0x01 Error 1 (UART Commu.)
0x02 Error 2 (Duplication)
0x03 Error 3 (IP Add Setting)
0x04 Error 4 (GW Add setting)
0x05 Error 5 (DNS1 Setting)
0x06 Error 6 (DNS2 Setting)
0x07 Error 7 (Sbnt Msk Setting)
0x00 100Mbps/Full Duplex
0x01 100Mbps/Half Duplex
0x02 10Mbps/Full Duplex
0x03 10Mbps/Half Duplex
0x04 Auto
0x68
0x70
Speed Setting
Yes
Yes
Yes
Yes
Enable
Disable
Enable
Enable
Input Skip
bit0
bit1
bit2
bit3
bit4
bit5
bit6
bit7
HD15
DVI
HDMI
VIDEO
S-VIDEO
Reserved
Reserved
Reserved
0x71
0x74
0x75
0x76
0x7A
Default Input
0x00 Last Memory
0x01 Option
Yes
No
Yes
Yes
Yes
Yes
Yes
Enable
Disable
Disable
Disable
Enable
Enable
Enable
Enable
Enable
Enable
Digital Signal Detect 0x00 VIDEO
(DVI/HDMI/etc.)
*6
0x01 PC
*7
Signal Status
0x00 Stable
No
0x01 Unstable/No Signal
VIDEO Signal Detect 0x00 NTSC
0x01 PAL
No
Logo Position
0x00 Auto
Yes
0x01 Landscape
0x02 Portrait
0x7D
Power Management 0x00 OFF
Yes
Yes
Disable
Enable
*8
Mode
0x01 ON
GXD-L52H1
7
Code Table (1-a)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Standby
Power On
0x7E
0x7F
On Screen Logo
0x00 OFF
Yes
Yes
Enable
Enable
0x01 ON (Default)
0x02 Reserved
0x00 OFF
LED
Yes
Yes
Disable
Enable
0x01 ON
*4:
*5:
Auto Signal Detect becomes Disable. When Option Slot is connected, Option command is Enable.
Restricts a part of keys operation following below.
[Remote Commander]
Menu, Picture, Sound, ECO (Power Saving), Contrast+/_,Brightness, Chroma, H Shift, V Shift, V size, PAP
[Main]
Menu
*6:
*7:
*8:
Digital Signal Status is Enable for Digital Input Signal Detect Function only in Stable.
Digital Signal or VIDEO Signal is Enable. Return Signal Status of Active Window.
Only the panel power supply is turned off at the standby when setting it “ON”.
5. Analog Signal Detect Function
(a) Mode Control
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
Code Table (1-a) [a]
Code Table (1-d)
0xFF
0xXX
Answer
Header
Answer
Return to Data Size
Return Data1
Data2
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (1-a) [b]
0xFF
0xXX
Completed
Code Table (1-a)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Yes
Standby
Disable
Power On
Enable
0x78
Analog Signal Detect 0x00 VIDEO
0x01 PC
No
Code Table (1-d)
Input Select
1-a[b]
0x00
0x01
0xFF
Main
When input is no signal or not supported signal, return value is Video(0x00).
Sub
Present input
GXD-L52H1
8
6. Priority Signal Select Function
(a) Mode Control
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
Code Table (2-a) [a]
Code Table (2-d)
0xFF
0xXX
Answer
Header
Answer
Return to Data Size
Return Data1
Data2
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (2-a) [b]
0xFF
0xXX
Completed
Code Table (2-a)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Standby
Power On
0x77
Priority Signal Select 0x00 Input1 Auto
0x01 Input1 RGB
No
Yes
Disable
Enable
0x02 Input1 YPbPr
Code Table (2-d)
Input Select
0x00
0x01
HD15
Option
(b) Color Matrix
Syntax
Header
Category
0x00
Function
Data1
Data2
Data3
Data4
Check Sum
Control
0x8C
Code Table
(1-b) [a]
0x04
Code Table
(1-c)
Code Table
(1-b) [b]
Code Table
(1-d)
0xXX
Syntax
Header
Category
Function
Code Table (1-b) [a]
Data1
Data2
Check Sum
Enquiry
0x83
0x00
Code Table (1-c)
Code Table (1-d) 0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x00
0x03
0x70
0x73
Completed
Command Canceled
Answer
Header
Answer
Return to
Data Size
Return Data1
Return Data2
Return Data3
Check
Sum
Enquiry
0x70
0x00
0x04
Code Table (1-c)
Code Table (1-b) [b]
Code Table (1-d) 0xXX Completed
Code Table (1-b)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Yes
Standby
Power On
0x1D
Color Matrix
0x00 YCbCr
0x01 YPbPr
Yes
Disable
Enable
GXD-L52H1
9
Code Table (1-c)
Format Select
0x00
0x01
0x02
0x03
480P
1080i
720P
480i
Code Table (1-d)
Input Select
0x00
0x01
HD15 (Component)
Option
(c) Time Control
Data Set (Month, Date)
Syntax
Header
Category
Function
Data1
Data2
Data3
Check Sum
Control
0x8C
0x00
0x7C
0x03
Month: 0x01-0x0C
Date: 0x01-0x1F
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
0xFD
Enquiry
0x83
0x00
0x7C
0xFF
0xFF
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x01
0x02
0x03
0x70
0x71
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Return Data2
Check Sum
0xXX
Enquiry
0x70
0x00
0x03
Month: 0x00-0x0C Date: 0x01-0x1F
Completed
Year Set
Syntax
Header
Category
Function
Data1
Data2
Check Sum
0xXX
Control
0x8C
0x00
0x7B
0x02
Year: 0x00-0x63
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
0x7B
0xFF
0xFF
0xFC
GXD-L52H1
10
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x01
0x02
0x03
0x70
0x71
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Year: 0x00-0x63
0xXX
Completed
Clock Set (Hour, Minute)
Syntax
Header
Category
Function
Data1
Data2
Data3
Check Sum
Control
0x8C
0x00
0x22
0x03
Hour: 0x00-0x17
Minute: 0x00-0x3B
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
0xA3
Enquiry
0x83
0x00
0x22
0xFF
0xFF
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x01
0x02
0x03
0x70
0x71
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Return Data2
Check Sum
*
Enquiry
0x70
0x00
0x03
Hour: 0x00-0x17
Minute: 0x00-0x3B
0xXX
Completed
Clock Set (Week)
Syntax
Header
Category
Function
Data1
Data2
Check Sum
0xXX
Control
0x8C
0x00
0x23
0x02
Week: Code Table (1-e)
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
0x23
0xFF
0xFF
0xA4
GXD-L52H1
11
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x01
0x02
0x03
0x70
0x71
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Week: Code Table (1-e)
0xXX
Completed
Code Table (1-e)
Week Select
0x00
0x01
0x02
0x03
0x04
0x05
0x06
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
On Timer, Off Timer
Syntax
Header
Category
Function
Data1
Data2
Data3
Check Sum
Control
0x8C
0x00
Code Table (1-f) [a]
0x03
Hour: 0x00-0x17
Minute: 0x00-0x3B
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
Code Table (1-f) [a]
0xFF
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x01
0x02
0x03
0x70
0x71
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Return Data2
Check Sum
Enquiry
0x70
0x00
0x03
Hour: 0x00-0x17
Minute: 0x00-0x3B
0xXX
Completed
GXD-L52H1
12
Code Table (1-f)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
On Timer
0x50 Sunday
_
_
_
_
_
_
_
_
Yes
Yes
Disable
Enable
0x51 Monday
0x52 Tuesday
0x53 Wednesday
0x54 Thursday
0x55 Friday
0x56 Saturday
0x57 Every day
Off Timer
0x58 Sunday
_
_
_
_
_
_
_
_
Yes
Yes
Disable
Enable
0x59 Monday
0x5A Tuesday
0x5B Wednesday
0x5C Thursday
0x5D Friday
0x5E Saturday
0x5F Every day
(d) IP Address Setting
IP Address
Syntax
Header
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x8C
0x00
0x42
0x05
Address 0
0x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
Subnet Mask
Syntax
Header
0x8C
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x00
0x61
0x05
Address 0
0x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
Gateway Address
Syntax
Header
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x8C
0x00
0x62
0x05
Address 0
0x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
DNS Primary
Syntax
Header
0x8C
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x00
0x63
0x05
Address 0
0x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
GXD-L52H1
13
DNS Secondary
Syntax
Header
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x8C
0x00
0x64
0x05
Address 0
0x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x00
0x03
0x70
0x73
Completed
Command Canceled
IP Address ex)
192.128.14.1 →192 (0xC0) Address 0
128 (0x80) Address 1
14 (0x0E) Address 2
1
(0x01) Address 3
* IP address command can be carried out even in the standby state.
Code Table (1-a)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Enable
Power On
0x42
0x61
0x62
0x63
0x64
IP Address
_
_
_
_
_
Yes
Yes
Enable
Subnet Mask
Gateway Address
DNS Primary
DNS Secondary
7. Picture/Sound
(a) Picture/Sound
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
Enquiry
0x8C
0x83
0x10
Code Table (2-a) [a] 0x02
0xFF
Code Table (2-a) [b]
0xFF
0xXX
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x01
0x02
0x03
0x70
0x71
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
0xXX
Enquiry
0x70
0x00
0x02
Code Table (2-a) [b]
Completed
GXD-L52H1
14
Code Table (2-a)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x00
0x01
0x02
0x03
0x04
Contrast
Brightness
Chroma
0x00-0x64
0x00-0x64
0x00-0x32
0x00-0x64
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Disable
Disable
Disable
Disable
Disable
Enable
Enable
Enable
Enable
Enable
Phase
Color Temp
0x00
Cool
0x01
Neutral
Warm
Custom
0x02
0x03
0x09
0x0A
Sharpness
NR
0x00-0x14
0x00
Yes
Yes
Yes
Yes
Disable
Disable
Enable
Enable
OFF
0x01
Low
0x02
Mid
0x03
High
0x0B
0x0C
Cinema Drive
0x00
Auto
Yes
Yes
Yes
Yes
Disable
Disable
Enable
Enable
0x01
OFF
Dynamic Picture
0x00
OFF
0x01
ON
0x02
Reserve
ON
0x0D
0x0E
Color Correct
0x00
Yes
Yes
Yes
Yes
Disable
Disable
Enable
Enable
0x01
OFF
Gamma Correct
0x00
High
0x01
Mid
0x02
Low
0x10
Picture Mode
0x00
Standard
Vivid
Yes
Yes
Disable
Enable
0x01
0x02
Custom
TC Control
Conference
0x05
0x06
0x30
0x31
0x32
0x33
0x34
Volume
0x00-0x64
0x00-0x64
0x00-0x64
0x00-0x64
0x00
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Enable
Disable
Disable
Disable
Disable
Enable
Enable
Enable
Enable
Enable
*1
Treble
*1
Bass
Balance
Surround
OFF
0x01
Hall
0x02
Simulate
Dynamic
Standard
Reserve
Custom
0x35
Sound Mode
0x00
Yes
Yes
Disable
Enable
0x01
0x02
0x03
(Continued)
GXD-L52H1
15
Code Table (2-a)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x36
0x37
Default Volume Set 0x00-0x64
Yes
Yes
Yes
Enable
Enable
Enable
Enable
Volume Select
0x00
0x01
0x32
0x46
0x64
Last Memory Yes
Default Setting
0x38
Max Volume Set
50
Yes
Yes
Enable
Enable
70
100
*1 Sound Mode = Custom Only is Enabled.
(b) Color Temp
Syntax
Header
Category
Function
Data1
Data2
Data3
Check Sum
Control
0x8C
0x10
Code Table (2-b) [a] 0x03
Code Table (2-c)
Code Table (2-b) [b]
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x10
Code Table (2-b) [a] Code Table (2-c)
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x00
0x03
0x70
0x73
Completed
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Return Data2
Check Sum
Enquiry
0x70
0x00
0x03
Code Table (2-c)
Code Table (2-b) [b] 0xXX
Completed
Code Table (2-b)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x05
0x06
0x07
Red Gain
Green Gain
Blue Gain
0x00-0x1E
Yes
Yes
Disable
Enable
Code Table (2-c)
Format Select
0x00
0x01
0x02
0x03
Cool
Neutral
Warm
Custom
GXD-L52H1
16
8. Size/Shift
(a) 8Bits Register
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
Enquiry
0x8C
0x83
0x20
Code Table (3-b) [a] 0x02
0xFF
Code Table (3-b) [b]
0xFF
0xXX
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x01
0x02
0x03
0x70
0x71
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
0xXX
Enquiry
0x70
0x00
0x02
Code Table (3-b) [b]
Completed
Code Table (3-b)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x00
0x01
0x02
0x03
0x04
H Size
H Shift
V Size
V Shift
Aspect
0x00-0x3C
0x00-0x3C
0x00-0x0A
0x00-0x3C
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Disable
Disable
Disable
Disable
Disable
Enable
Enable
Enable
Enable
Enable
0x00 Wide Zoom
(VIDEO Only)
0x01 Zoom
(VIDEO Only)
0x02 Full
(VIDEO Only)
0x04 Normal
(PC:Real, VIDEO: 4:3)
0x05 Full 1 (PC Only)
0x06 Full 2 (PC Only)
0x00 OFF
0x05
Multi Display
Yes
Yes
Disable
Enable
0x01 2 x 2
0x02 3 x 3
0x03 4 x 4
0x04 1 x 2
0x05 1 x 3
0x06 1 x 4
0x07 2 x 1
0x08 3 x 1
0x09 4 x 1
(Continued)
GXD-L52H1
17
Code Table (3-b)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x06
0x07
Auto Pixel Adjust
Dot Phase
0xFF Execute
0x00-0x1F
Yes
Yes
Yes
No
Disable
Disable
Disable
Enable
Enable
Enable
Yes
Yes
0x0B Multi Position
(2 x 2 ,1 x 2, 2 x 1)
0x00 Position1
0x01 Position2
0x02 Position3
0x03 Position4
0x00 Position1
0x01 Position2
0x02 Position3
0x03 Position4
0x04 Position5
0x05 Position6
0x06 Position7
0x07 Position8
0x08 Position9
0x00 Position1
0x01 Position2
0x02 Position3
0x03 Position4
0x04 Position5
0x05 Position6
0x06 Position7
0x07 Position8
0x08 Position9
0x09 Position10
0x0A Position11
0x0B Position12
0x0C Position13
0x0D Position14
0x0E Position15
0x0F Position16
0x00 OFF
*1
0x0C Multi Position
Yes
Yes
Disable
Enable
(3 x 3, 1 x 3, 3 x 1)
*1
0x0D Multi Position
Yes
Yes
Disable
Enable
(4 x 4, 1 x 4, 4 x 1)
*1
0x0E Over Scan
Yes
Yes
Yes
Yes
Disable
Disable
Enable
Enable
0x01 ON
0x02 AUTO
0x0F
Multi Display
0x00 Tiles
Output Format
0x01 Window
GXD-L52H1
18
*1 Arrangement of Multi Position.
Multi Position (2 x 2)
Multi Position (1 x 2)
Multi Position (2 x 1)
1
3
2
4
1
2
1
2
Multi Position (3 x 3)
Multi Position (1 x 3)
Multi Position (3 x 1)
1
4
7
2
5
8
3
6
9
1
2
3
1
2
3
Multi Position (4 x 4)
Multi Position (1 x 4)
Multi Position (4 x 1)
1
5
9
2
6
3
7
4
8
1
2
3
4
1
2
3
4
10 11 12
13 14 15 16
GXD-L52H1
19
9. Status Enquiry
(a) Model Name
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x00
0xFF
0xFF
0xB1
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
0xXX
Enquiry
0x70
0x00
0x02
Code Table (4-a)
Completed
Code Table (4-a)
Format Select
0x26
GXD-L52H1
(b) Serial Number
Syntax
Header
Category
Function
Data1
0xFF
Data2
Check Sum
Enquiry
0x83
0x30
0x01
0xFF
0xB2
Answer Header Answer Return to
Data Size
Return Data1 Return Data2 Return Data3 Return Data4 Check Sum
Enquiry 0x70
0x00
0x05
Upper 8bit
Data
Middle Upper
Data
Middle Lower Lower 8bit
Data Data
0xXX
Completed
Return Data1-Data4: 0x00000000-0x0098967F (0,000,000-9,999,999)
(c) Operation Time
Syntax
Header
Category
Function
Data1
0xFF
Data2
Check Sum
0xB3
Enquiry
0x83
0x30
0x02
0xFF
Answer Header Answer Return to
Data Size
Return Data1 Return Data2 Return Data3 Return Data4 Check Sum
Enquiry 0x70
0x00
0x05
Upper 8bit
Data
Middle Upper
Data
Middle Lower Lower 8bit
Data Data
0xXX
Completed
Return Data1-Data4: 0x00000000-0xD693A3FF (0sec.-3,599,999,99sec.)
(d) Soft Version (Main CPU)
Syntax
Header
Category
Function
Data1
0xFF
Data2
Check Sum
Enquiry
0x83
0x30
0x03
0xFF
0xB4
Answer Header
Enquiry 0x70
Answer
Return to Data Size
Return Data1
Upper 8bit Data
Return Data2
Check Sum
0x00
0x03
Lower 8bit Data 0xXX
Completed
Return Data1-Data2: 0x0000-0xFFFF (BCD Format)
ex) In Version0.100, it is set to 01 and 00.
GXD-L52H1
20
.
.
For function 0x07, 0x08, 0x09, 0x10, 0x12, 0x13,
0x14 and 0x16 in the left table
When the display value is 3.0 V, “0x1E” (30) is
returned.
For function 0x0A, 0x0B and 0x0C, 0x0D in the
left table
When the display value is 50 dC, “0x32” (50) is
returned.
When the display value is _20 dC, “0xEC” is
returned.
(e) 8bits Register
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
Code Table (4-b)
0xFF
0xFF
0xXX
Answer Header
Enquiry 0x70
Answer
Return to Data Size
Return Data1
Check Sum
0x00
0x02
Code Table (4-b) 0xXX
Completed
Code Table (4-b)*
Function
Return Data
Unit
*
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x11
0x12
0x13
0x14
0x16
Digital 3.3 V
Analog 24 V
Digital 5 V
Temp1
0x00-0xFF
0x00-0xFF
0x00-0xFF
0x00-0xFF
0x00-0xFF
0x00-0xFF
0x00-0xFF
0: Normal, 1: Abnormal
0x00-0xFF
0x00-0xFF
0x00-0xFF
0x00-0xFF
0x00-0xFF
Temp2
Temp3
Temp P/S
Inverter Alarm
Shutdown Log
Digital 3.3 V (Failure)
Digital 5 V (Failure)
Analog 12 V (Failure)
Analog 12 V
(f) Shutdown Log
Syntax
Header
Category
Function
Data1
0xFF
Data2
Check Sum
Enquiry
0x83
0x30
0x11
0xFF
0xC2
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Shutdown Log
0xXX
Completed
Code Table (4-c)
Return Data1: 0x00-0xFF
Code Table (4-c)
Shutdown Information
bit0 Reserved
bit1 1: FAN Sensor Abnormal
bit2 1: Panel Abnormal
0: Normal
0: Normal
0: Normal
bit3 1: Temperature Sensor Abnormal
bit4 Reserved
bit5 1: Power Abnormal (3.3 V, 5 V)
0: Normal
bit6 1: Analog Power Abnormal (12 V, 9 V, 5 V) 0: Normal
bit7 Reserved
GXD-L52H1
21
(g) Auto Input Detect
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x30
0xFF
0xFF
0xE1
Answer Header Answer Return to
Data Size
Return Data1 Return Data2 Return Data3 Return Data4 Return Data5
Enquiry 0x70
0x00
0x0C
Input1
Input2
Input3
Input4
Input5
Input Type
Code Table
(4-e)
Input Type
Code Table
(4-e)
Input Type
Code Table
(4-e)
Input Type
Code Table
(4-e)
Input Type
Code Table
(4-e)
Return Data6 Return Data7 Return Data8 Return Data9 Return Data10
Option1
Option1
Option2
Option2
Option3
Option Type
Code Table
(4-e)
Input Type
Code Table
(4-e)
Option Type
Code Table
(4-e)
Input Type
Code Table
(4-e)
Option Type
Code Table
(4-e)
Return Data11 Check Sum
Option3
0xXX
Completed
Input Type
Code Table
(4-e)
Code Table (4-e)
Input
Input Type (Basic)
Option Type
Input Type (Option)
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
OPTION1
0x06 RGB/YUV (Analog)
0x07 DVI
0x00 No Input
0x00 No Input
0x00 No Input
0x00 Analog Only
0x00 Analog Only
0x00 Analog Only
0x00 Analog Only
0x01 Analog/Com
0x03 Com Only
0x00 No Input
0x03 Video/S-Video
0x06 RGB/YUV (Analog)
0x07 Video/S-Video/RGB/YUV (Analog)
0x04 RGB
0x00 No Input
0x04 Digital Only
0x04 Digital Only
0x00 Analog Only
0x00 Analog Only
0x0E Digital/Digital
0x0D Digital
OPTION2
OPTION3
0x00 No Input
0x00 No Input
GXD-L52H1
22
(h) Auto Plug Detect
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x32
0xFF
0xFF
0xE3
Answer
Header
Answer
Return to Data Size
Return Data1
Return Data2
Return Data3
Enquiry
0x70
0x00
0x21
Panel Type
Code Table (4-h)
H_Resolution (H)
Code Table (4-i)
H_Resolution (L)
Code Table (4-i)
Return Data4
Return Data5
Return Data6
Return Data7
V_Resolution (H)
Code Table (4-i)
V_Resolution (L)
Code Table (4-i)
Input Quantity
Code Table (4-j)
Input1
Input Type
Code Table (4-e)
Return Data8
Return Data9
Return Data10
Return Data11
Input2
Input3
Input4
Input5
Input Type
Code Table (4-e)
Input Type
Code Table (4-e)
Input Type
Code Table (4-e)
Input Type
Code Table (4-e)
Return Data12
Return Data13
Return Data14
Return Data15
Option Slot Quantity
Code Table (4-j)
Option1
Option Type
Code Table (4-e)
Option1
Input Type
Code Table (4-e)
Option2
Option Type
Code Table (4-e)
Return Data16
Return Data17
Return Data18
Return Data19
Option2
Input Type
Code Table (4-e)
Option3
Option Type
Code Table (4-e)
Option3
Input Type
Code Table (4-e)
(Reserve)
0xFF
Return Data20
Return Data21
Return Data22
Return Data23
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
Return Data24
Return Data25
Return Data26
Return Data27
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
Return Data28
Return Data29
Return Data30
Return Data31
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
Return Data32
Check Sum
(Reserve)
0xFF
0xXX
GXD-L52H1
23
(i) Auto Panel Type Detect
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x31
0xFF
0xFF
0xE2
Answer
Header
Answer
0x00
Return to Data Size
Return Data1
Code Table (4-h)
Check Sum
Enquiry
0x70
0x02
0x72
Completed
Code Table (4-h)
Code Table (4-i)
Code Table (4-j)
H_Resolution
V_Resolution
0x0780 (1920)
0x0438 (1080)
Input Quantity
0x05
0x01
Panel Type
Option Slot Quantity
0x00
LCD
Code Table (4-d)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
Enable
0x00
0x01
0x02
Model Name
0x26
No
Yes
Enable
Serial Number
Operation Time
0x000
0x00000000-0x15751BF0
(0sec.-359,996,400sec.)
0x03
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x11
0x12
0x13
0x14
0x16
0x30
0x31
Soft Version (Main)
Digital 3.3 V
Analog 24 V
Digital 5 V
0x0000-0x9999
0x00-0xFF
0x00-0xFF
0x00-0xFF
Temp1
0x00-0xFF
Temp2
0x00-0xFF
Temp3
0x00-0xFF
Temp P/S
0x00-0xFF
Inverter Alarm
Shutdown Log
0: Normal, 1: Abnormal
0x00-0xFF
Digital 3.3 V (Failure)
Digital 5 V (Failure)
Analog 12 V (Failure)
Analog 12 V
0x00-0xFF
0x00-0xFF
0x00-0xFF
0x00-0xFF
Auto Input Detect
Auto Panel Type Detect
GXD-L52H1
24
10. User Reset
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x50
Code Table (5) 0x02
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x00
0x03
0x70
0x73
Completed
Command Canceled
Code Table (5)
Function
Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x00
0x01
0x02
0x03
Picture Reset
Yes
No
Disable
Enable
Audio Reset
Size Reset
Size, Shift
Picture Reset2
(FW50)
Contrast, Brightness,
Chroma, Phase
0x04
All Reset
11. Service
(a) Mode
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0xF0
Code Table (6) 0x02
0xFF
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0xF0
0x00
0xFF
0xFF
0x71
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x00
0x03
0x70
0x73
Completed
Command Canceled
Answer
Header
Answer
0x00
Return to Data Size
0x02
Return Data1
Code Table (7)
Check Sum
Enquiry
0x70
0xXX
Completed
Code Table (6)
Function
Range/Switch code
Command
Control
Standby
Power On
Normal Mode Service Mode
0x00
0x01
Service Mode IN
Service Mode Exit
Yes
Yes
Yes
Yes
Yes
Yes
Enable
Disable
Enable
Enable
GXD-L52H1
25
Code Table (7)
Function
Range/Switch code
Command
Enquiry
Standby
Power On
Normal Mode Service Mode
Disable Enable
0x00
0x01
User Mode
Service Mode
Yes
Yes
Yes
(b) Factory Reset
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x40
Code Table (8) 0x02
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x03
0x73
Command Canceled
Code Table (8)
Function
Range/Switch
code
Command
Control
Enquiry
Standby
No
Power On
Normal Mode Service Mode
Disable Enable
0x88 Factory Reset
Yes
No
Yes
GXD-L52H1
26
The material contained in this manual consists of
information that is the property of Sony Corporation.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens de
l’équipement à moins d’une permission écrite de Sony
Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen
Ausrüstung
ohne
ausdrückliche
schriftliche Erlaubnis der Sony Corporation.
GXD-L52H1
Printed in Japan
2008. 1 22
©2008
GXD-L52H1 (WW) E
9-968-408-01
Sony Corporation
|